Hybrid eXtreme Uniclamp™ X-Clamp Repair Kit (w/Paste + eXtras + Tools)
In deze kit zitten vele extra's ten opzichte van de oude kit, ook de Xbox 360 Toolkit zit er gratis bij!!!
This is our newest revision of the Hybrid eXtreme Uniclamp™ X-Clamp Repair Kit it includes all necessary tools, like screwdrivers, opening tools, and a 5mm metal drill and sand paper for the standoffs, as well as two alcohol wipes to clean off the chip dies!
Furthermore we added some additional eXtras which will further help the cooling of your console and increase the lifetime of the fix, you now get our RAM Pad Cooling Kit and 2 RAM heatsinks as well as 1g of our eXtreme Cool 360 Thermal Compound.
This kit is a compilation of all tools required for the hybrid fix and saves you the money buying these tools separately, over all you would otherwise pay around 40 Euro for all the parts you get here.
Material included in the kit:
Includes:
-Hybrid eXtreme Uniclamp(TM) backplate with eXtreme-Cool 360(TM) Thermal Pads for CPU/GPU.
8x M5 14mm perfect fit cheese-head metric screws and 40x M5 1mm steel washers
1 gram eXtreme-Cool 360(TM) Gaming Thermal Compound (nano-carbon technology)
1x set Xbox 360 Hybrid eXtreme Foam Shims(TM) GPU&CPU (upgraded for 2011)
2x RAM/Chipset Aluminum Heatsinks
1x eXtreme-Cool 360(TM) Thermal Pad RAM Cooling Kit 6 pieces (for Ram under GPU heatsink and under mobo)
-Xbox 360 Opener Tool
-Torx T8 and T10 L key
-> The L key can also be used for xbox 360 wireless controllers(got a hole in the middle), and it of course works for all types of case screws, the bigger T10 ones, as well as the small T8 ones(The old red screwdriver isnt in it anymore)
1x sheet of sand paper (to level standoffs in older units)
1x 5mm steel drill bit (needed for enlarging screw holes)
2x alcohol prep wipes (for prepping chips/heatsinks)
The Hybrid Advanced kit is the ultimate way to fix your Xbox 360 console.
It corrects the failed metal case design amongst with the X-Clamps and can be called the first real X-Clamp Replacement, as the X-Clamp is replaced with the Uniclamp the key element of our new fix.
The initial problem is that heat and especially the flexing caused by these flaws stress the solder balls under the GPU and CPU and in the end cause the solder balls to become cold and loose contact.
At first these design flaws are corrected by flattening the case out to prevent the console from failing again.
The actual fix consists mainly out of the Uniclamp Advanced and the Hybrid Advanced Foam Shims, the Uniclamp is placed on the bottom of the case and the foam shims fill out the gap in between the outer parts of the chip.
Then the heatsinks are mounted and the mainboard is fixed to the case with 8 M5 machine screws, when these are tightened the foam pads of the Uniclamp compress and develop a counter force on the chip from below while the foam shims and the chip die are pushed down evenly by the heatsink. Like that the solder balls in between chip and mainboard which have become disconnected are pressed effectively back together and are thereby reconnected which allows the console to function again.
This even counter-pressure is the difference to all other fixes the pressure is shared up on the whole chip, also the outer parts thanks to the shims, not just the center of the die this always led to flexing and the reversed flexing effect of the X-Clamps.
To prevent the mainboard from flexing downwards the pads from the uniclamp keep the mainboard leveled with the counterpressure and also strengthen the sandwich effect which keeps the solder joint reconnected
In addition the mainboard is fixed to the case which gives it more stability.
This fix contains the good parts from all older fixes and new features for newly discovered issues and can thereby consider itself to be the most up-to-date and thereby best fix out in the wild.
Op onze forum vind u meer info, foto's en een uitgebreide handleiding van deze kit.
